SYNTH ZONE
Visit The Bar For Casual Discussion
Topic Options
#97932 - 10/15/03 09:14 AM Yamaha PA-3B and PA-3C adapters??????
squeak_D Offline
Senior Member

Registered: 10/08/00
Posts: 4715
Loc: West Virginia
Can the PA-3B or PA-3C adapters be subsituted with anything from Radio Shack? There much smaller and I was curious if you could get the same thing through Radio Shack for less.

Thanks.
Squeak
_________________________
GEAR: Yamaha MOXF-6, Casio MZX-500, Roland Juno-Di, M-Audio Venom, Roland RS-70, Yamaha PSR S700, M-Audio Axiom Pro-61 (Midi Controller). SOFTWARE: Mixcraft-7, PowerTracks Pro Audio 2013, Beat Thang Virtual, Dimension Le.

Top
#97933 - 10/15/03 10:55 AM Re: Yamaha PA-3B and PA-3C adapters??????
travlin'easy Offline
Senior Member

Registered: 12/08/02
Posts: 15556
Loc: Forest Hill, MD USA
Squeak,

As long as the adapter meets both the voltage and amperage requirments, and has the same polarity, then any adapter meeting those standards will suffice. Radio shack sells lots of adapters, however, most only go up to 12 volts DC. The PA-300 Yamaha adapter is a 16-volt DC power pack, which is now the norm for the PSR-1000, 2000 and 2100. To my knowledge, no one sells this type of adapter other than Yamaha and it goes for a hefty $75.

Cheers,

Gary
_________________________
PSR-S950, TC Helicon Harmony-M, Digitech VR, Samson Q7, Sennheiser E855, Custom Console, and lots of other silly stuff!

K+E=W (Knowledge Plus Experience = Wisdom.)

Top
#97934 - 10/15/03 11:17 AM Re: Yamaha PA-3B and PA-3C adapters??????
Scottyee Offline
Senior Member

Registered: 12/01/99
Posts: 10427
Loc: San Francisco Bay Area, CA, US...
Squeak: The PA-3B is rated DC 12V 700mA so I believe the Radio Shack '12V/1000mA AC-to-DC' Power Adapter is the correct one to get:
http://www.radioshack.com/product.asp?ca...5Fid=273%2D1776

The PA-3B output delivers 700mA while the above Radio Shack adapter delivers 1000mA. This is fine because your keyboard will draw ONLY the amount of current 'it actually needs'. A problem will arise only if you use an AC adapter which puts out 'less than' the required 700mA.

As far as the plug goes, take your PA-3B into the Radio Shack store and select the appropriate plug (adaptaplug) that matches the plug size/type of the PA-3B. A very IMPORTANT thing to remember is to be sure you select the plug with the correct polarity type required by your keyboard):

1. positive tip (+)
or
2. negative tip (-)

The Adapter Plug tip type (tip+ or tip-) is often specified in a schematic illustration situated right next to the actual plug input on the keyboard itself, and sometimes also in the owner's manual.

Good luck,

Scott

[This message has been edited by Scottyee (edited 10-15-2003).]
_________________________

Top
#97935 - 10/15/03 02:56 PM Re: Yamaha PA-3B and PA-3C adapters??????
Dnj Offline
Senior Member

Registered: 09/21/00
Posts: 43703
I would listen to Gary and be VERY CAREFULL what you plug into your KB other then the original factory A/C adapter.

Top
#97936 - 10/15/03 03:09 PM Re: Yamaha PA-3B and PA-3C adapters??????
squeak_D Offline
Senior Member

Registered: 10/08/00
Posts: 4715
Loc: West Virginia
Actually the adapter would be for the Yamaha QY-100. It uses the smaller adapter, and I was curious if I could buy a substitute at the Shack..

Squeak
_________________________
GEAR: Yamaha MOXF-6, Casio MZX-500, Roland Juno-Di, M-Audio Venom, Roland RS-70, Yamaha PSR S700, M-Audio Axiom Pro-61 (Midi Controller). SOFTWARE: Mixcraft-7, PowerTracks Pro Audio 2013, Beat Thang Virtual, Dimension Le.

Top
#97937 - 10/15/03 04:28 PM Re: Yamaha PA-3B and PA-3C adapters??????
YamahaUS1 Offline
Member

Registered: 10/24/02
Posts: 238
Loc: Buena Park, CA, USA
Squeak,
I will second the warning to be very careful. We've had no complaints about the quality of Radio Shack's adapters, but you only get to mess up on the polarity 1 time. Then you're off to the servicer for a non warranty repair.



------------------
Steve Deming
Assistant Manager
Customer Support Dept.
Pro Audio & Combo Division
Yamaha Corporation of America
YCASupport@yamaha.com
714.522.9000
_________________________
Yamaha Customer Support
www.yamaha.com/pacsupport
714.522.9000

Top
#97938 - 10/15/03 04:30 PM Re: Yamaha PA-3B and PA-3C adapters??????
Pilot Offline
Member

Registered: 11/14/02
Posts: 328
Loc: Ontario,Canada
My old PSR220 requires a PA-3/3B but I'm using one of those Radio Shack switchable voltage PSUs that puts out 800mA. I did some voltage measurments on it and found the following: set to 12V the off load voltage was 16V, at 250mA the output voltage was 13.5 V and at 800mA the voltage was 10V. Set to 9V the corresponding voltages were 12.2, 10.5 and 7.5. Not what you would call regulated. It works OK with the PSR at the 12V setting because the output chip can take 25V and the rest of the circuitry has regulators which can take care of the overvoltage. I wouldn't be surprised if the the QY has similar hardware.

Bryan

Top

Moderator:  Admin, Diki, Kerry 



Help keep Synth Zone Online